Page History

...

On cruises with short transit times, perform, in port, as many of these the following as possible.:

Lab orientation/Introduction

...

Prepare reagents

Prepare the following reagents according to the recipes in the user guides. Remember to put your initials and the date on all reagents made.

• • Alkalinity/pH/chloride titrations
• Coulometer
• IC
• ICP
SPEC
• • • Alkalinity: Prepare 20 mM and 40 mM standards if necessary 
    • Chlorinity: Prepare 2 liters of dilution solution
  • Coulometer
    • HCl solution, KOH and AgNO3 solutions if needed
  • IC 
    • all solutions except for anion eluent, which should be made shortly before analysis
    • pourable calibration standards
  • ICP
    • 2% and 3% TM nitric acid solutions, also 10% if analyzing hard rock
    • internal standard(s)
    • primary in-house cocktail
    • pourable in-house and IAPSO calibration standards
  • SPEC
    • Ammonium
      • Ammonium standard (dry ammonium chloride in oven overnight) + calibration standards
      • alkaline solution
    • Phosphate 
      • Phosphate primary standard (dry monobasic potassium phosphate in oven overnight) + calibration standards
      • Sulfuric acid solution
      • Antimony potassium tartrate solution
      • Ammonium molybdate solution

Check gas bottles

Check the pressure of the oxygen (ChemLabchem lab), helium and argon bottles (Tween Pallet Stores). Ensure the bottles are above 200 psi; otherwise, swap them out with fresh bottles. When a Pallet Stores bottle array is empty, tear the yellow tags to EMPTY, disconnect the manifold and connect it to full bottles (see how to do this). It is good practice to always have a full gas bottle array ready to go. 

...

Fill the 20 L Nalgene tub with 18 L DI water. Place the tub in the fume hood nearest the Nanopure system and slowly add 2 L concentrated HCl. This will be used to clean labware (glass and plastic. NO metal).
Fill one of the small tubs with 10% nitric (reagent) to clean ICP vials/bottles and fill the other small tub with 10% nitric (trace metal) for the cleaning of XRAY crucibles only. 

Freeze Dryer

Make sure that the freeze dryer is operating. The vacuum pump is located inside, behind the front stainless panel. Check vacuum pump oil level.

...

• • • Obtain the IW sampling interval from the Curator and take the sample(s) when the core comes on deck.
    • If possible, have the geochemist assist you in determining where to take the IW sample. Never take a sample that includes a change in lithology.
    • Initially, 5 cm whole rounds are taken; as the water yield decreases, go to 10 cm whole rounds. Larger whole rounds may be taken after speaking to the SAC (Curator, EPM, and co-chiefs).
    • If possible, take the IW sample from the bottom of the same section every time. As recovery decreases you will have to take the IW sample from wherever you can.
    • A typical IW sampling plan is for 0 – 100 mbsf, take one IW per core and > 100 mbsf, take one IW every third core. Check with the Curator on the current plan.
    • Note the core, section and interval of the sample and write it on the Curator's logsheet. The interval will be entered into SampleMaster by the Curator/ALO.

...

• • • Alkalinity/pH - If there is ample water, allocate 5 mL for shipboard analyses (alkalinity, salinity, IC, SPEC). Speak with the scientists about which analyses they would or wouldn't like performed (ie. Make a priority list). Extra water may be used for repeat analysis or stored (sent back to the repository).
    • Scientific party - split and store the remaining water into the requested aliquots as outlined by the sampling plan. Each sample's storage/preservation is up to its requestor.
    • ICP – 1 - 2 ml; must be acidified with trace metal-grade nitric acid (~ 30 10 µL).
    • Remove the plunger from the syringe, rinse with DI water and place in the HCl bath for twelve hours. Rinse the components with DI water and bake dry at a low temperature. When completely dry, reassemble syringes and store them in ziploc bags.

...

Crushing, weighing and running carbonate samples require a significant portion of time. During the initial discussion of the sampling protocol the scientists will decide where they want to take the sample(s) for the carbonate/EA analyses. It can be taken from the IW squeezecake and/or at the sample table after the core is split. Either way, these samples will have to be freeze-dried (typically for twelve hours) and then crushed/homogenized using a mortar and pestle. Usually the scientists will prepare and run the analyses, and using a mortar and pestle. Usually the technician will set up the system and both scientists and technicians will weigh and run the analysis.

CHNS

Again, weighing and running the samples on this instrument is time-intensive and it be best to have a good sized batch ready before running. Usually the scientists will weigh out the samples and the technician will set up the instrument and sequencessystem and both scientists and technicians will weigh and run the analysis. Replace the combustion column after approximately 100 samples.

...

• Write the End-of-Expedition lab report and send a copy, via e-mail, to the on-coming technicians.
• Make sure all data is sent to LIMS and all raw data files are copied to the Data1 volume. 
• Pack up equipment being returned for repairs and give the ALO the following information: IODP inventory number, value, serial number, model number, vendor's name and country of manufacture.
• Pack up all samples as per scientists' requests; work with the Curator/ALOs.
• Give the LO a list for port purchases, if any.
• Clean the lab and assigned area following the cleaning instruction according to LO's list. Bring all the trash to the incinerator. Glass and sharps get disposed of in port call.
• Check the oil in the freeze dryer's vacuum pump.
• Defrost and clean the freeze dryer.
• Clean (defrost if necessary) the fridges; dispose of old reagents.
• Check the ovens for debris. Clean them. 
• Clean any instrument-specific items.
• Have the lab coats laundered (segregated and tumble dried).
• Check expiration dates on chemicals, notify ALO/LO if there are hazardous chemicals/waste to be disposed of in port.
• Confirm that both helium and argon have a new full rack of gas bottle connected and ready to go.

VI. Port call – Off Going

...